![]() Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the program’s code IKEv1, IKEv2, with 5 encryption methods for IPsec (DES, 3DES, AES128, AES192, AES256)Ĭlient/Server instances can run simultaneously, L2TPv3 support Multiple clients and a server can run simultaneously, 12 encryption methodsĭES-CBC, RC2-CBC, DES-EDE-CBC, DES-EDE3-CBC, DESX-CBC, BF-CBC, RC2-40-CBC, CAST5-CBC, RC2-64-CBC, AES-128-CBC, AES-192-CBC, AES-256-CBC Pre-configured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI DMZ NAT NAT-TĭDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks)īlacklist for blocking out unwanted websites, Whitelist for specifying allowed sites onlyįlexible access control of TCP, UDP, ICMP packets, MAC address filter Pre-shared key, digital certificates, X.509 certificates Possibility to mount remote file system via SSH protocol Wired WAN options, each of which can be used as an automatic Failoverīalance Internet traffic over multiple WAN connections Supported >25 service providers, others can be configured manually Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e Static and dynamic IP allocation, DHCP Relay Port forwards, traffic rules, NAT rules, custom rules Ping Reboot, Wget reboot, Periodic Reboot, LCP and ICMP for link inspection H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets ![]() TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, FTP, SMTP, SSL v3, TLS, ARP, PPPoE, UPNP, SSH, DHCP, Telnet client, SNMP, MQTT, Wake on LAN (WOL) So i'm assuming that they are using a stunnel)Īre they using STUNNEL ? since the message for connecting is differnt from the other messages i got.1 x WAN port, 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX crossoverĤ x LAN ports (can be configured as secondary WAN ports), 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX crossover So this tells me the clients both connect with the syslog server ( they only connect when I start STUNNEL on the clients. When i check /var/log/secrue it wil show the following output: I have created a new certificate stunnel.pem on the server. I have changed /etc/nf on the cliend and the server. is stunnel holding some cache i have to empty first or what ? Now when i start stunnel on both client as server i'l get the error in /var/log/secure: On the server side i did the same thing, i've created a file on the client named and copied form the server the certificate syslog-ng-server.pem into. Ok now i copied from the CLIENT the certificate into a new file on the server named ( wich i created with VI and copy/paste with VI) Then i move syslog-ng-client.pem to /etc/stunnelĬert = /etc/stunnel/syslog-ng-cli ent.pemĬAfile = /etc/stunnel/syslog-ng-ser ver.pemĬonnect = :5140 (server IP) Make syslog-ng-client.pem and hit enter a few times ( left the fields empty). Here i've created this file named: nfĬert = /etc/stunnel/syslog-ng-ser ver.pemĬAfile = /etc/stunnel/syslog-ng-cli ent.pemĪccept = :5140 (server IP) Then i move syslog-ng-server.pem to /etc/stunnel ![]() Make syslog-ng-server.pem and hit enter a few times ( left the fields empty). ![]() I followed this step by step, and it used to work from 1 machine but not from the 2nd I'm not very known with SSL/certificates so i followed this guide to setup syslog-ng + stunnel. I'm also using STUNNEL/SSL to encrypt the messages going from client to server. I'm using syslog-ng server for both client and server. I'm setting up a syslog-ng server so i can log my clients logs on a server. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |